Monthly Archives: October 2012

Is this good enough?

Posted on by

As the Bugatti waits for the Araldite to set so the steering wheel can be complete again and the grass is still too damp to mow, it seems I have run out of excuses to get the Sizaire out of the nursing home where she seems quite happily ensconced.

I had previously removed the cylinder to check the condition of the valves which turned out OK.  However the top of the cylinder water jacket has been leaking at the seams so after presenting the 31mm nut holding it together first with heat – fail, then with an impact wrench – fail, then finally swinging on a 4 foot bar – success!

Unfortunately ignorance was bliss but too late now  Pictures below:

bbblbbbr
img_1454_0.jpg
img_1455a.jpg
img_1444.jpg
img_1451.jpg
img_1454_0.jpg
img_1455a.jpg
img_1444.jpg
img_1451.jpg
img_1454_0.jpg
img_1455a.jpg
img_1444.jpg
img_1451.jpg
img_1454_0.jpg
img_1455a.jpg
img_1444.jpg
img_1451.jpg

So it looks like Colin gets some more work making a new stud and maybe brazing the water jacket, so Sizaire will continue to rest and is probably dreaming why most of her contemporaries get to rest in nice museums without the bother of their parts being interfered with.

Clutch Re-resolved?

Posted on by

Went for a shake down run to Mt Tarrengower (600kms return) and found the following small problems with the Bug:

  • Gearbox still noisy in top. Remedy: Earplug right ear.√
  • Radiator cap leaks. Remedy: nylon spacer and O ring.√
  • Fuel pressure too high. Remedy: 1 psi pressure relief valve on tank.
  • Sore arse (LHS). Remedy: Remove padding on prop shaft cover.√
  • Oil all over luggage. Remedy: put them in garbage bag next time.√
  • Clutch sticking. Remedy see below.√
  • Piece of steering wheel timber fell off. Remedy glue back on….if I can find it.

The run to Mt Tarrengower was wet, cold then sunny.  The car was surprisingly comfortable the trick being to lean forward when you see a woof in the road otherwise it was just a hoot to drive, it’s the first vintage car I’ve driven where you look forward to gear changes. However the clutch started to stick half way not wanting to return.  I did jury rig it so the external springs were doing all the work which they are not supposed to and I got home.

The previous owner had installed a clutch pedal stop, I of course could not see any reason for it so it was removed ..one should really think before doing such things, as it turned out when I was pushing the clutch to its now full unrestricted travel the release bearing was being impaled on the output flange resulting in the end being chewed up so it could not return.

So 2 or 3 hours later after some creative work with the Dremel all the dags have been removed, the clutch now works as it should mais until I reinstall the pedal stop I’m not going anywhere.

The Sizaire valves have been removed and were perfect so that only leaves everything else but as Andrew says “most fuel problems are the magneto” so I think I had better take his advice.

Type 37 at Lochinver Homestead

Sizaire Exhaust Valve, Big Yes?

Spring Cleaning

Posted on by

Everyone should invite a car club to their garage at least once a year for a Garage Crawl, apart from the obvious opportunity to show off the real reason is that you at last will see a reason to clean up the junk you’ve been tripping over for the last year and maybe some serious rearranging that never seemed to happen otherwise. As I never got around to painting the floor I will abstain from eating off it but it’s not bad all the same, tomorrow they arrive.
As this is the first entry for some time you would be right thinking that I have been slacking off, the Bugatti is now running well, the Douglas survived a 3 day rally without mishap but the Sizaire is still waiting for some attention. So instead of methodically working through this problem I have removed the cylinder and am currently trying to remove the inlet valve cage so the hopefully burnt exhaust valve will be exposed. I really have no evidence to support this theory it’s just the way my brain seems to be working at the moment so have decided to enjoy the challenge of disassembling something that has not yet been pulled apart.
Here is a picture of how not to remove the valve cage with a slide hammer. Currently cylinder is resting on bench waiting for another random attack from yours truly.